Hamiterge® 711-2 is an extremely high strength powdered alkaline cleaner consisting of exceptional wetting agents and detergents in a base of alkaline builders. It is an immersion cleaner designed for low or high temperature applications. It will remove rolling oils and other mill soils from all steel surfaces, including stainless and galvanized. It is also applicable for use in high speed scrubber systems. It is lower foaming at higher operating temperatures, (160 F and above) and is completely free rinsing with water. It is also available in a low foam version (Hamiterge® 711-2-LF) for spray washers. Hamiterge® 2031-C2 is a concentrated liquid alkaline spray cleaner for removal of rolling oil residues, metallic chips and fines, oily soils, and shop or mill dirt from sheet steel surfaces and other ferrous metal parts. It is designed for usage in power spray washers or roto-brush type cleaning equipment at elevated or ambient temperature conditions in dilutions with water. It is low foaming, completely biodegradable and free rinsing. It splits out cleaned soils readily and maintains low foaming characteristics when soils accumulate that can form soaps. Immunol® S-10 is for all general cleaning and degreasing of ferrous and non-ferrous parts, replacing flammable, toxic solvents and alkaline cleaners. Emulsifies oils, mill soils and provides mild indoor rust protection in one operation. For use as vibratory finishing additive, in steel mills, metalworking plants, paper and textile mills as a “general purpose” immersion cleaner. Widely used in tumbling, vibratory finishers, and as a “bucket” cleaner. Immunol ® Extra-J a detergent, wetting agent and rust preventive for cleaning and protecting most ferrous metals against rust. Not suitable for use on cast iron and cast steel. Replaces Immunol® Extra and contains no nitrosamines. Immunol® 1921 is a combination cleaner and rust preventive concentrate for use as a vibratory de-burring compound with water on castings of iron, steel or aluminum. Immunol® 985-J is a low foaming detergent spray cleaner for metal surfaces. It contains rust preventives which protect ferrous metals after cleaning for short periods indoors. It is a completely nitrite free product. It removes mineral and fatty mill soils completely without saponification; therefore, it is not spent in use. Immunol® 517-JV is an in-plant rust preventive for ferrous surfaces including cast and malleable iron, in hydostatic and ultrasonic testing, in spray washers for mild cleaning and rust inhibition, in one or two stages. It can be added to tumbling media for cleaning and rust inhibition, as a dip after tumbling, and as a grinding coolant-mixed with water, as well as a water quench after heat treating. Hamiterge® 8922 is a concentrated liquid alkaline spray cleaner for removal of rolling oil residues, drawing and stamping lubricants, rust preventives, metallic chips and fines, and other oily soils, shop or mill dirt from steel strip, wire, rod and bars. It is designed for use in power spray washers or roto-brush type cleaning equipment at elevated or ambient temperatures in dilutions with water. It is low foaming, completely biodegradable, and free rinsing. It will not buildup hard water deposits and contains no phosphates. Activol® 1357 is an additive for sulfuric, hydrochloric, nitric and hydrofluoric acid pickling and cleaning solutions and may be used as specialty additive on titanium in nitric acid baths. Activol® 1357 reduces surface tension, accelerates acid action and provides detergency in solution. This product also serves as a mild inhibitor to minimize acidic attack on base metal during scale removal. It promotes complete rinsing and reduces fume formation. Activol® 9012 is a powdered inhibitor for use in pickling operations using sulfamic acid. It imparts maximum inhibiting properties to sulfamic acid solutions reacting on steel. Use at 1-2% of the sulfamic acid weight in pickling baths, for reducing metal loss, fume prevention and reduction of hydrogen embrittlement. This product is also used to clean boilers or other steam generation equipment where sulfamic acid is utilized. Citriterge® 8910 is a cleaner consisting of natural citrus based solvents, surfactants and detergent components. It is designed to remove dirt, grease, oil and carbon smuts from metals and other hard surfaces. It also removes tar, pitch, asphalt, and gum soils from felts in papermaking operations. Citriterge® 8910 performs heavy duty cleaning without the use of petrochemical solvents, chlorinated solvents and harsh acids or alkalis. Hamico® 578-C is a liquid rust remover concentrate designed to dissolve rust on contact with steel or iron surfaces. The time required for rust removal is dependent on the degree of rust present. It removes light rust in a few minutes. Heavy rust will require longer times and may need repeated rinsing and application. It conforms to the general requirements of Mil Spec. M-10578-C, Type IV. Hamistrip® 1650 is for easy removal of most shop soils like soluble oil, grease and metal chips and fines. It is an alkaline rust and paint remover combining caustics and organic acids Hamiterge® 711-5 is a powdered alkaline cleaner designed for immersion cleaning of mill soils from steel surfaces and can be used on aluminum, copper and brass. It is also available in a low foam version (Hamiterge® 711-5-LF) for spray washers. Hamiterge® 1934-RP is a concentrated liquid emulsion cleaner for removal of oily films, metallic chips and fines, shop or mill dirt, and lube oil residues from steel, cast iron and aluminum surfaces. It is designed for use in single stage cleaning operations; immersion tanks or roto-brush type washers at elevated or ambient temperatures. It may be used diluted with hot or cold water and is free rinsing. It provides rust protection to steel and it is non-staining to aluminum. Immunol® 791-J is a mild detergent and rust inhibiting chemical for use on cast iron, cast steel and other ferrous metals. It protects cast iron and ferrous metals submerged in its solution indefinitely. It forms invisible, quick drying protective coatings on metal, which insure maximum “indoor” protection. Immunol® 1357-2-J is a clear, medium body, green liquid. It is odorless, non-flammable and pH 7.0 neutral. It is used in paper manufacturing as calendar roll cleaner and felt conditioner. It is used as additive to soluble oil (or synthetic) systems to emulsify “tramp” or hydraulic oil, loosen sludge, settle heavy particles, lift “fines” or lighter bodies to the surface. This product prevents stains or rust on ground or polished work and prevents “smut” formation in rolling when added to the soluble rolling oil. It is also a successful and economical machine, floor and wall cleaner mixed with plain water at 2 to 6 ounces per gallon and applied by brush, mop, or rag. Immunol® AC-11 is a cleaner/brightener for usage in vibratory finishing or tumbling operations. A mildly acidic compound, it brightens steel, copper or brass parts. It provides detergency and wetting to suspend and carry off oils and smut from the surface of the metal parts being cleaned. It will not rust steel media. It is inhibited against attack on aluminum, so it will not etch the surface. This product is compatible with plastic, steel or ceramic media. Immunol® S-6-H is a detergent type cleaner for soak tank cleaning and degreasing of ferrous and non-ferrous parts. It emulsifies oils such as drawing compounds and rust preventives, and removes mill soils and smut very effectively. It may also be used for general purpose cleaning as a “bucket” solvent to replace more flammable or toxic materials. If used on aluminum, extended immersion times (one hour or more) produce darkening. Use Immunol® S-6-I as an alternative for aluminum. Purgitol® RPV-1 is a liquid metal cleaner concentrate for use in immersion tanks, ultrasonic cleaning, or rotary barrel cleaning systems. Its use is for removal of oily soils, such as machining, grinding, or drawing oil residues, synthetic coolants, rust preventives, lubricating oils, and rolling oils. It can be used on steel, cast and malleable iron, and non-ferrous metal surfaces. Purgitol® S is the answer for machine shops seeking to replace toxic, odorous, irritating solvents in their immersion cleaning operations. Purgitol® S cleans machining and drawing oils and lubricants, yet it contains no flammable or toxic ingredients. | 
