Aquatemp® 8304-WT is a new synthetic chemical mill cleaner/rust preventive combination providing maximum “dry finish” rust protection. It is used where no reduction is required or desired as in “skin passing,” or “wet tempering.” It can be applied in conventional ways via spray headers at the entry side of the mill or with an air wipe on the delivery side. Steelgard® 1302-J is for rust protection of all ferrous metals, including cast and malleable iron. It is ideal for spray washer application for mild cleaning and rust protection. Aquatemp® 1860-LV-2 is a low viscosity temper mill lubricant for application on coated products during tempering or “skin pass” processes. It cleans the mill and strip, reduces roll pickup, permits higher mill speeds than dry tempering operation and provides lubrication to achieve required elongations. It is a solvent based product which evaporates after processing and can be coated with petroleum based coating oils. Hamico® 138-L is designed for use as a vanishing oil. It contains lubricity additives which make it ideal for stamping, blanking or drawing of light to medium gauge steel and aluminum. Hamico® 138-L has extremely low odor, is non-emulsifying, has a rapid evaporation rate, and leaves minimal residue. Application of the lubricant can be via spraying, flooding or swabbing. Hamico® 863-EP Base is normally used as received, but can be diluted with oil, solvents, or water, depending on the operation. It may be applied by dipping, spray, or brushing. It is a combination of extreme pressure lubricants. It is used either neat or with oil. It is used primarily for tapping operations on steel. It will not corrode steel or aluminum on contact, but will stain brass and copper. Hamico® 8906-WT Rinse Aid is a stain preventing additive for rinse systems following hydrochloric or sulfuric acid pickling operations. It is an acidic product possessing corrosion protection and wetting. It is designed to eliminate the brown or reddish stains often experienced on steel exiting a continuous pickler. It eliminates the formation of iron hydroxide slimes which accumulate in rinse tanks as a result of acid bath carryover. Hamidraw® 1829 is an ultra-heavy duty, water soluble, extreme pressure lubricant, offering maximum lubricity for drawing, ferrous and non-ferrous metals, including stainless steel. It is designed for extremely difficult draws to provide maximum extreme pressure lubrication and is non-staining to metals and carbide dies. The residual film offers corrosion protection for the drawn parts. If diluted at 1:1 with water, Hamidraw® 1829 forms a low viscosity, stable emulsion. Hamidraw® 1829 can also be diluted with petroleum solvents or mineral oils. Hamidraw® 1829 is suited to spray application or direct flood application onto workpiece or dies. Hamiterge® 711-2 is an extremely high strength powdered alkaline cleaner consisting of exceptional wetting agents and detergents in a base of alkaline builders. It is an immersion cleaner designed for low or high temperature applications. It will remove rolling oils and other mill soils from all steel surfaces, including stainless and galvanized. It is also applicable for use in high speed scrubber systems. It is lower foaming at higher operating temperatures, (160 F and above) and is completely free rinsing with water. It is also available in a low foam version (Hamiterge® 711-2-LF) for spray washers. Hamiterge® 711-5 is a powdered alkaline cleaner designed for immersion cleaning of mill soils from steel surfaces and can be used on aluminum, copper and brass. It is also available in a low foam version (Hamiterge® 711-5-LF) for spray washers. Hamiterge® 1457 is a combination of soaps, detergents and wetting agents designed for paper mill felt scouring. Due to its low alkalinity, it will not harm woolen or semi-synthetic felts, yet will remove soils that may remain after acid cleaning. Hamiterge® 2031-C2 is a concentrated liquid alkaline spray cleaner for removal of rolling oil residues, metallic chips and fines, oily soils, and shop or mill dirt from sheet steel surfaces and other ferrous metal parts. It is designed for usage in power spray washers or roto-brush type cleaning equipment at elevated or ambient temperature conditions in dilutions with water. It is low foaming, completely biodegradable and free rinsing. It splits out cleaned soils readily and maintains low foaming characteristics when soils accumulate that can form soaps. Hamiterge® 8922 is a concentrated liquid alkaline spray cleaner for removal of rolling oil residues, drawing and stamping lubricants, rust preventives, metallic chips and fines, and other oily soils, shop or mill dirt from steel strip, wire, rod and bars. It is designed for use in power spray washers or roto-brush type cleaning equipment at elevated or ambient temperatures in dilutions with water. It is low foaming, completely biodegradable, and free rinsing. It will not buildup hard water deposits and contains no phosphates. Immunol® 517-JV is an in-plant rust preventive for ferrous surfaces including cast and malleable iron, in hydostatic and ultrasonic testing, in spray washers for mild cleaning and rust inhibition, in one or two stages. It can be added to tumbling media for cleaning and rust inhibition, as a dip after tumbling, and as a grinding coolant-mixed with water, as well as a water quench after heat treating. Immunol® 985-J is a low foaming detergent spray cleaner for metal surfaces. It contains rust preventives which protect ferrous metals after cleaning for short periods indoors. It is a completely nitrite free product. It removes mineral and fatty mill soils completely without saponification; therefore, it is not spent in use. Purgitol® S-8 is a concentrated liquid cleaner for rolling oil and other mill soil removal from steel strip by application through spray headers at the last stand on a four or five stand cold reducing tandem mill. Purgitol® S-8 may also be used as a water soluble straightener lubricant for wire or rods on roll straightener equipment. It has excellent corrosion protection, boundary lubrication and is low foaming (for recirculating sprays). Steelgard® 2005 is a new innovation for use as a temper mill fluid for coated products replacing straight oils, solvents or the practice of dry tempering. In addition to preventing white rust, it produces a better “healed-over” surface, reduces roll pick-up, permits higher mill speed and achieves elongations with lower roll force. Mill Purge® 1812 is an industrial maintenance cleaner for floors, machinery, sumps, kettles and vats, etc. It is also used in ultrasonic cleaning, dip tank cleaning of steel, cast iron and aluminum parts and equipment. Steelgard® 20-M-1 Base is a long term indoor rust preventive base for all ferrous surfaces including bearings type and tool steels. Offering excellent non-staining property on stainless or alloys, it can be used in neat form for maximum protection but is generally used cut with from one to nine parts diluting oil or solvents. It is available in ready-to-use dilutions with mineral spirits, kerosene, 100 viscosity group I oil, mineral seal oil and similar vehicles. Steelgard® 1505-B is designed for long term, thin film corrosion protection for ferrous and non-ferrous surfaces. It displaces moisture and leaves a thin, clear, non-staining film that dries to the touch in three hours. It is readily removed by mineral spirits or mild alkali washes. Steelgard® 1505-M is a solvent based rust preventive with a high flash point for use on steel and cast iron. It provides 6-12 months indoor storage protection under normal humidity conditions. Steelgard® 8703-AT is a solvent based corrosion preventive for steel and cast iron which provides long term indoor protection against rust for periods up to 24 months under normal conditions. It can also provide protection under cover outdoors for up to six months. It is a low odor rust preventive, which leaves a dry film less than a mil in thickness. Steelgard® 9060 is a water borne corrosion inhibitor for outdoor (covered), limited outdoor uncovered (up to 30-40 days), and indoor protection to steel & ferrous alloys. It is a ready to use product straight from the container and dries to a dry, transparent film that will not re-emulsify when exposed to moisture in the air. Steelgard® 9060 will provide excellent protection to metals under indoor or covered outdoor conditions. This product is particularly helpful where the need to reduce VOC emission levels is critical. | 
