Hamico® 1003 is a light colored, transparent, odorless lubricating oil for machinery and equipment requiring an extremely clean condition with a light oil. It can be used in many applications where light lubrication is needed, e.g., forming, bending, stamping, straightening. It can be used on all metals as received, by pumping, dip, spray or wipe. Steelgard® X-267-B is a long term, outdoor rust preventive that can be used on ferrous or non-ferrous metals, in uncovered or covered storage conditions. It protects tools, stampings, forgings, castings, machinery, tubing or any metal parts that need a waxy, plastic, non-tacky film. It protects overseas and domestic shipments. Steelgard® 8920-K is an indoor rust preventive for steel stored in an acidic atmosphere such as a pickling department. It is designed primarily for protection against hydrochloric (muriatic) acid vapors. It deposits an oily film and is a very low odor product. It protects against staining and contact corrosion in tightly wrapped steel coils. Hamico® 863-EP Base is normally used as received, but can be diluted with oil, solvents, or water, depending on the operation. It may be applied by dipping, spray, or brushing. It is a combination of extreme pressure lubricants. It is used either neat or with oil. It is used primarily for tapping operations on steel. It will not corrode steel or aluminum on contact, but will stain brass and copper. Hamidraw® 497-B is composed of extreme pressure resisting chlorinated base and synthetic esters. It contains no pigments, is non-flammable and is completely removable in mineral or chlorinated solvents. It will not channel and is cohesive and adhesive. The viscosity of this product can be reduced by cutting back with solvents or mineral oils. Hamidraw® 497-MX-2 is composed of extreme pressure resisting chlorinated base and synthetic esters. Pigmented and non-flammable, this product is completely removable in mineral solvents, chlorinated solvents and hot alkaline cleaners. It will not channel and is cohesive and adhesive. The viscosity of this product can be reduced by cutting back with solvents or mineral oils. Hamidraw® 1846-B is a heavy duty pigmented drawing lubricant for ferrous or stainless steels. It is utilized for extremely severe draws such as tube reducing, bar drawing, wire drawing when reductions up to 40% are required. The lubricant cleans quickly with hot alkaline or hot detergent cleaning. Hamidraw® 1846-NC is a heavy duty non-chlorinated pigmented drawing lubricant for ferrous or stainless steels. It can be used for severe draws such as tube reducing, bar drawing, wire drawing, etc. The lubricant cleans quickly with hot alkaline or hot detergent cleaning. Hamidraw® 1945 Series (100-700) is a lubricant for blanking and deep drawing of all metals. It is a heavy duty oil and can be cut back with mineral oil for lighter work. Removal from the metal can be done with solvents or alkaline cleaners. Hamidraw® 1945 is offered in various viscosity grades. Hamidraw® 9100-B is an entirely non-chlorinated extreme pressure lubricant for heavy duty drawing and stamping. It contains a polymeric lubricant package which provides the extreme pressure lubricating properties of the chlorinated additives formerly used. Hamidraw® 9100-B is environmentally acceptable and has enhanced removability characteristics. Hamilube® 1328-N contains no chlorinated compounds and only minimal amounts of sulfur and phosphorus. It has a light viscosity to flush away metal chips and provide efficient heat removal from the work and tooling. It is suitable for machining operations such as trepanning, threading, tapping, turning, milling and drilling of steel. Hamilube® 1744 is a straight oil containing extreme pressure additives for general machining of all metals, including Magnesium. Hamilube® 1955-A is a straight oil non-chlorinated lubricant that contains extreme pressure additives for the general machining of tool steel and stainless steel. It contains no chlorinated compounds or phosphorus. It is transparent to allow viewing of the work piece during machining. It is not suitable for use with non-ferrous metals. It contains active sulfur and is non-staining on steel. Hamilube® 5705 is a straight oil containing extreme pressure additives for the general machining of tool steel and stainless steel. It contains no chlorinated compounds, phosphorus or animal fats. Not suitable for use with non-ferrous metals. Hamilube® 7609 is a low viscosity straight oil containing friction-reducing extreme pressure additives, which makes it suitable for drilling operations. It is also applicable for threading, tapping, turning, milling, trepanning and other machining operations on steel. A combination of extreme pressure additives, along with its light viscosity, makes it suitable for gun drilling. It will provide an adequate fluid film between the wear pads and the work material, will prevent welding of chips to the cutting edge of the drill, will cool the drill and the work, and dispose of the chips easily by flushing. Hamilube® 7709 is a non-chlorinated straight oil containing friction-reducing extreme pressure additives, which makes it suitable for drilling operations. It is also applicable for threading, tapping, turning, milling, trepanning and other machining operations on steel. Used on Stainless and Alloyed steels. It contains sulfurized additives and has a light viscosity, which makes it suitable for gun drilling. It will provide an adequate fluid film between the wear pads and the work material, will prevent welding of chips to the cutting edge of the drill, will cool the drill and the work, and dispose of the chips easily by flushing. Hamilube® 9200-VP is a chlorine free lubricant for the grinding and light machining of steel, copper, bronze or brass. It is a straight petroleum based lube containing an advanced additive package that is free of sulfur, chlorine, and pigmented compounds. It has excellent lubrication characteristics that compares very favorably to chlorinated and sulfurized lubes. While it is designed for use neat, as received, it can be cut back with mineral oil or solvents for lighter work. Removal of the residue from the metal can be performed with solvent degreasing, detergent, or alkaline cleaning. Steelgard® 40-M-1 Base is an indoor rust preventive base for all ferrous surfaces including bearing steels, and tool steels. It is a barium free product. It can be used neat for maximum protection, but is generally used cut with from one to nine parts diluting oil or solvents. It is available in ready-to-use dilutions with mineral spirits, kerosene, 100 viscosity group I oil, mineral seal oil and similar vehicles. Steelgard® 1938-K-1 is a solvent based rust preventive for steel, iron or non-ferrous metals protection under normal indoor storage conditions. It provides 6 to 12 months protection in a normal warehouse storage environment. | 
